En-suite Tile Calculator — 5m x 5m Room with 330 x 330mm Tiles

Room Details

Tell us about your space and we'll do the rest.

metres
metres

Total tiles needed

249

tiles (including 10% wastage)

Floor Area

25.0

Tiles (no waste)

226

Extra for cuts

+23

125

Tile Adhesive

125 kg

6 × 20kg bags, 1 × 5kg bag

8.8

Grout

8.8 kg

1 × 5kg bag, 1 × 2.5kg bag, 1 × 10kg bag

Your Shopping List

6

Tile Adhesive (20kg bag)

Flexible wall & floor adhesive

1

Tile Adhesive (5kg bag)

Flexible wall & floor adhesive

1

Grout (5kg bag)

Flexible wall & floor grout

1

Grout (2.5kg bag)

Flexible wall & floor grout

1

Grout (10kg bag)

Flexible wall & floor grout

How Many Tiles May You Need?

For a 5m x 5m en-suite with 330 x 330mm tiles, our estimate suggests you may need around 249 tiles to cover the 25m² floor area, including an allowance for waste and cuts. Since this is a wet area, you'll likely need water-resistant adhesive and proper waterproofing behind the tiles to help prevent moisture damage. Choosing suitable materials for a en-suite is important for long-lasting results. This guide walks you through the key considerations for tiling your en-suite floor.

How to Measure Your En-suite

Accurate measurements are the foundation of any successful tiling project. Measure the length and width of your en-suite at the widest points, as most rooms are not perfectly rectangular. Work in metres for consistency with tile coverage calculations. For rooms with alcoves or recesses, break the space into rectangular sections and add them together. To check your room is square, use the 3-4-5 triangle method: measure 3 metres along one wall, 4 metres along the adjacent wall, and the diagonal between should be 5 metres. If the room is out of square, you may need to plan your tile layout to minimise awkward cuts at the edges.

Choosing 330 x 330mm Tiles for Your En-suite

Your chosen 330 x 330mm tiles are a versatile, mid-range size that works well in almost any room. They strike a good balance between ease of installation and visual appeal, with fewer grout lines than small tiles but without the substrate demands of large format tiles. In a bathroom, this size provides a good balance of grip and easy cleaning. Always order a few extra tiles beyond the estimated amount in case of breakages during cutting or for future repairs.

Tile Layout Patterns

The two most common floor tile layouts are straight (grid) and diagonal (diamond). A straight layout is simpler to install and typically requires around 10% extra tiles for waste from cuts at the edges. A diagonal layout creates a more dynamic look but increases waste to approximately 15%, as more cuts are needed where tiles meet the walls at an angle. Brick bond (staggered) is another popular alternative that adds visual interest without the extra waste of a diagonal layout. With a larger floor area, you have the freedom to experiment with diagonal or herringbone patterns that can add real character to the space. Whichever pattern you choose, always dry-lay a few rows first to check the look before committing with adhesive.

Suggested Materials

Based on your 5m x 5m en-suite (25m²), the estimated quantity is approximately 249 tiles, around 125kg of adhesive (roughly 7 x 20kg bags), and approximately 8.8kg of grout (roughly 2 x 5kg bags). For a en-suite, use a flexible, waterproof adhesive such as BAL Rapid-Flex or Mapei Keraquick. Standard adhesive is not suitable for wet areas as it can break down with prolonged moisture exposure. Always buy slightly more than estimated to account for any wastage during mixing.

Installation Tips

Start by finding the centre of your en-suite and snapping chalk lines to create a cross. Begin tiling from the centre outwards so that any cut tiles at the edges are symmetrical. Use tile spacers to maintain consistent grout joints and check your work regularly with a spirit level to ensure tiles are flat and even. Before tiling a en-suite, apply a tanking membrane or liquid waterproofing primer to the floor and at least 150mm up the walls. This is essential to prevent water seeping into the subfloor and causing damage. Allow the adhesive to cure for at least 24 hours before grouting, and avoid walking on the tiles during this time.

Estimated Cost

Tile prices in the UK vary widely depending on material and finish. For your 25m² en-suite, budget tiles typically cost between £10-20/m² (£250-500), mid-range options run £20-40/m² (£500-1000), and premium tiles can be £40-80/m² (£1000-2000). Adhesive costs around £15-25 per 20kg bag (£105-175 for your project), and grout is approximately £8-15 per 5kg bag (£16-30). If you need a wet tile cutter, hire is typically around £30 per day. In total, you might expect to spend between £401 and £2235 depending on your tile choice and whether you hire tools.

Frequently Asked Questions

How many 330 x 330mm tiles do I need for a 5m x 5m en-suite?

For a 5m x 5m en-suite (25m²), you will need approximately 249 tiles of 330 x 330mm size. This total includes an allowance for waste from cuts at the edges of the room. We recommend buying an extra 2-3 tiles beyond this number in case of breakages during cutting or for future repairs.

How much tile adhesive do I need for 25m²?

For a 25m² floor area, you will need approximately 125kg of tile adhesive. This is roughly 7 x 20kg bags. For a en-suite, use a flexible waterproof adhesive such as BAL Rapid-Flex or Mapei Keraquick to protect against moisture damage.

Should I use 330 x 330mm tiles in a en-suite?

Mid-range tiles are versatile and work well in most rooms. They balance ease of installation with a clean, modern appearance. In a en-suite, this size offers a good compromise between grip and easy cleaning. Ensure you use water-resistant grout.

What grout width should I use for 330 x 330mm tiles?

For 330 x 330mm tiles, a grout joint width of 3mm is the standard recommendation for most ceramic and porcelain tiles. If your tiles are rectified (precision-cut with perfectly straight edges), you can use a narrower 2mm joint for a sleeker, more seamless appearance. For natural stone tiles, a slightly wider 4-5mm joint is often recommended to accommodate the natural variation in tile edges. Always use tile spacers to maintain a consistent joint width throughout your en-suite.

These calculations are estimates based on standard manufacturer coverage rates. Actual quantities may vary depending on surface conditions, wastage, and application technique. Always verify quantities with your supplier before purchasing.

Related Calculators